Range Rover Evoque: Inner Constant Velocity (CV) Joint Boot

Special Tool(s)

303-D121
Puller, General Purpose

General Equipment

Removal

NOTE: RH inner constant velocity joint boot shown, LH is similar.

1. Refer to: Front Halfshaft LH (205-04 Front Drive Halfshafts, Removal and Installation).

Refer to: Front Halfshaft RH - LHD AWD/RHD AWD (205-04 Front Drive Halfshafts, Removal and Installation).

Refer to: Front Halfshaft RH - FWD (205-04 Front Drive Halfshafts, Removal and Installation).

2. NOTE: Discard the retaining clips. General Equipment: Vise

Range Rover Evoque. Front Drive Halfshafts

3. CAUTION: Make sure that filings and swarf do not enter the component.

NOTE: Some variation in the illustrations may occur, but the essential information is always correct.

Range Rover Evoque. Front Drive Halfshafts

4. NOTE: Discard the retaining clip.

Range Rover Evoque. Front Drive Halfshafts

5. Special Tool(s): 303-D121

Range Rover Evoque. Front Drive Halfshafts

Installation

1. CAUTION: Extreme cleanliness must be exercised when handling these components. Clean and inspect the components for deterioration.

2.

Range Rover Evoque. Front Drive Halfshafts

3. NOTE: Install a new retaining clip.

Range Rover Evoque. Front Drive Halfshafts

4. CAUTION: Make sure that these components are installed to the noted removal position.

Range Rover Evoque. Front Drive Halfshafts

5. Pack the inner CV joint with the grease supplied.

6. NOTE: Install new retaining clips.

Range Rover Evoque. Front Drive Halfshafts

7. Refer to: Front Halfshaft LH (205-04 Front Drive Halfshafts, Removal and Installation).

Refer to: Front Halfshaft RH - LHD AWD/RHD AWD (205-04 Front Drive Halfshafts, Removal and Installation).

Refer to: Front Halfshaft RH - FWD (205-04 Front Drive Halfshafts, Removal and Installation).

Outer Constant Velocity (CV) Joint Boot

General Equipment

Removal

1. WARNING: Make sure to support the vehicle with axle stands. Raise and support the vehicle.

2. Refer to: Inner Constant Velocity (CV) Joint Boot (205-04 Front Drive Halfshafts, Removal and Installation).

3. NOTE: Discard the retaining clips. General Equipment: Vise

Range Rover Evoque. Front Drive Halfshafts

Installation

1. CAUTION: Extreme cleanliness must be exercised when handling these components. Clean and inspect the components for deterioration.

2. Pack the outer CV joint with the grease supplied.

3. NOTES:

Install new retaining clips.

Some variation in the illustrations may occur, but the essential information is always correct.

Range Rover Evoque. Front Drive Halfshafts

4. Refer to: Inner Constant Velocity (CV) Joint Boot (205-04 Front Drive Halfshafts, Removal and Installation).

READ NEXT:

 Front Halfshaft RH FWD

Special Tool(s) 205-857 Remover, Halfshaft Removal CAUTIONS: Nuts and bolts must be tightened with the weight of the vehicle on the suspension. Do not allow halfshafts to hang unsupported at one end

 Rear Drive Halfshafts

 Rear Halfshaft LH

Special Tool(s) 205-857 Remover, Halfshaft 205-928 Remover, Half Shaft Inboard Joint Removal CAUTIONS: Nuts and bolts must be tightened with the weight of the vehicle on the suspension. Do not allow

SEE MORE:

 Cleaning after off-road driving

Ensure that the areas around air intakes and the front grille are clean and clear of debris. Pay particular attention to the lower grille and radiator. Failure to do so may cause the engine to overheat, leading to severe engine damage. Ensure that the vehicle underside is cleaned as soon

 System difficulties

Use of an incorrect program will impair the vehicle's response to the terrain and can reduce the life of the suspension and drive systems. If the system becomes partially inoperable for any reason, it may not be possible to select special programs. A warning will be given when selection of

© 2011-2025 Copyright www.rrevoque.org