Range Rover Evoque: Transmission GTDi 2.0L Petrol - Removal
Special Tool(s)
205-857
Remover, Halfshaft
303-021
Engine support bracket
303-662
Support Beam Arm and Hook Assembly, Engine
JLR-303-1591
Lifting Bracket, Engine - Rear
General Equipment
- Transmission jack
NOTE: Some variation in the illustrations may occur, but the essential information is always correct.
1. Refer to: Plenum Chamber (412-01 Climate Control, Removal and Installation).
2. Refer to: Starter Motor (303-06B Starting System - GTDi 2.0L Petrol, Removal and Installation).
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
- Repeat the above step for the other side.
- Secure the hood at the highest position.
15. Repeat the above step for the other side.
16.
17.
18.
- Special Tool(s): JLR-303-1591
Torque: 24 Nm
19. Support the engine.
Special Tool(s): 303-021, 303-662
20.
21.
22.
23. WARNING: Make sure to support the vehicle with axle stands. Raise and support the vehicle.
24. Remove the front wheels and tires.
Refer to: Wheel and Tire (204-04 Wheels and Tires, Removal and Installation).
25. Refer to: Engine Undershield (501-02 Front End Body Panels, Removal and Installation).
26. Refer to: Front Subframe (502-00 Uni-Body, Subframe and Mounting System, Removal and Installation).
27. CAUTIONS:
Be prepared to collect escaping fluids.
Make sure that all openings are sealed. Use new blanking caps.
NOTE: Remove and discard the O-ring seals.
28. CAUTION: Discard the nut.
29. CAUTIONS:
Make sure that the driveshaft is supported with suitable retaining straps.
Do not use a hammer to detach the halfshaft from the hub assembly, failure to follow this instruction may result in damage to the halfshaft.
Special Tool(s): 205-857
30. WARNING: Be prepared to collect escaping fluids.
CAUTION: Keep the halfshaft horizontal to avoid damaging the oil seal.
31.
32. CAUTION: Inspect the seal, replace if damaged If removed for access only.
33. CAUTION: Discard the nut.
34. CAUTIONS:
Make sure that the driveshaft is supported with suitable retaining straps.
Do not use a hammer to detach the halfshaft from the hub assembly, failure to follow this instruction may result in damage to the halfshaft.
Special Tool(s): 205-857
35.
36. WARNING: Be prepared to collect escaping fluids.
CAUTION: Keep the halfshaft horizontal to avoid damaging the oil seal.
37.
38. CAUTION: Discard the bolts.
Tie aside.
39.
40.
41.
42.
43.
44.
45. CAUTION: Discard the bolts.
46. General Equipment: Transmission jack
47.
48.
49. CAUTIONS:
Make sure that the torque converter remains in the transmission.
Make sure that the dowels are still located on the engine and not the transmission.
50. NOTE: Do not disassemble further if the component is removed for access only.
51.
READ NEXT:
Transmission GTDi 2.0L Petrol - Installation
Installation
NOTE: Some variation in the illustrations may occur, but the essential
information is always correct.
1. NOTE: This step is only required if previously removed.
Torque: 12 Nm
2. NOTE:
Transmission Control Module (TCM) TD4 2.2L
Diesel
Removal
1. Disconnect the battery ground cable.
Refer to: Specifications (414-01 Battery, Mounting and Cables,
Specifications).
2. Refer to: Air Cleaner (303-12, Removal and Installation).
3.
4.
5
Torque Converter Seal TD4 2.2L Diesel
Special Tool(s)
307-597
Installer, Torque Converter Seal
307-613
Holding Pins, Torque Converter
Removal
NOTE: Some variation in the illustrations may occur, but the essential
information is always co
SEE MORE:
Powered tailgate opening height
The maximum opening height can be set as
required. This is useful in parking areas with
low ceiling heights or just for ease of use.
1. Open the tailgate to the position which you
want to set as the maximum height. Press
any tailgate control to stop movement at
the required position. Final pos
Inner Quarter Panel
Removal
NOTES:
The inner quarter panel is manufactured from mild steel.
There are NVH components on this panel, they are not serviced on the new panel.
If damaged, new components will be required.
1. The front inner quarter panel is replaced in conjunction with:
Rear bumper cover
Quarter panel
