Range Rover Evoque: Transfer Case Seal
LH GTDi 2.0L Petrol
Special Tool(s)
100-012
Slide Hammer
205-873/1
Remover/Installer, Transfer Case Seal
205-873/2
Protector, Transfer Case Seal
205-873/3
Punch/Screws, Transfer Case Seal
Removal
NOTES:
Removal steps in this procedure may contain installation details.
Some variation in the illustrations may occur, but the essential information is
always correct.
1. WARNING: Make sure to support the vehicle with axle stands.
Raise and support the vehicle.
2. Refer to: Power Transfer Unit - GTDi 2.0L Petrol (308-07B Transfer
Case - Vehicles With: AWF21 6-Speed Automatic Transmission/M66
6-Speed Manual Transmission AWD, Removal and Installation).
3. CAUTIONS:
Take extra care not to damage the seal.
Inspect the seal, replace if damaged
4. CAUTIONS:
Make sure that the area around the component is
clean and free of foreign material.
Take extra care not to damage the mating faces.
- Special Tool(s): 205-873/1
- Special Tool(s): 205-873/2
- Special Tool(s): 205-873/3
5.
- Special Tool(s): 205-873/1
- Special Tool(s): 205-873/2
- Special Tool(s): 205-873/3
6.
- Special Tool(s): 205-873/1
- Special Tool(s): 205-873/2
- Special Tool(s): 205-873/3
- Special Tool(s): 100-012
Installation
1. CAUTION: A soft faced hammer should be used to
avoid damaging the special tool and creating debris.
- Special Tool(s): 205-873/1
- Special Tool(s): 205-873/2
- Special Tool(s): 205-873/3
2. To install, reverse the removal procedure.
3. Refer to: Power Transfer Unit - GTDi 2.0L Petrol (308-07B Transfer
Case - Vehicles With: AWF21 6-Speed Automatic Transmission/M66
6-Speed Manual Transmission AWD, Removal and Installation).
4. Check and top-up the transfer case fluid level.
Refer to: Transfer Case Fluid Level Check (308-07B Transfer Case -
Vehicles With: AWF21 6-Speed Automatic Transmission/M66 6-Speed Manual
Transmission AWD, General Procedures).
READ NEXT:
Special Tool(s)
100-012
Slide Hammer
205-873/1
Remover/Installer, Transfer Case Seal
205-873/2
Protector, Transfer Case Seal
205-873/3
Punch/Screws, Transfer Case Seal
Removal
NOTES:
Removal steps in
Special Tool(s)
100-012
Slide Hammer
205-872
Installer, Transfer Case Seal
308-615
Remover, Seals
308-617
Depth Drill, Seal Remover
Removal
NOTES:
Removal steps in this procedure may contain installat
Special Tool(s)
100-012
Slide Hammer
205-872
Installer, Transfer Case Seal
308-615
Remover, Seals
308-617
Depth Drill, Seal Remover
Removal
NOTES:
Removal steps in this procedure may contain installat
SEE MORE:
Removal
NOTE: Removal steps in this procedure may contain installation details.
All vehicles
1. Make the SRS system safe.
Refer to: Standard Workshop Practices (100-00 General Information,
Description and Operation).
2. Disconnect the battery ground cable.
Refer to: Specifications (414-01 Battery
Removal
1. Refer to: Rear Quarter Panel Moulding (501-08 Exterior Trim and
Ornamentation, Removal and Installation).
2. Refer to: B-Pillar Upper Trim Panel - 3-Door (501-05 Interior Trim and
Ornamentation, Removal and Installation).
3. Refer to: D-Pillar Trim Panel (501-05 Interior Trim and
Ornament
© 2011-2024 Copyright www.rrevoque.org