Range Rover Evoque: Exterior Trim and Ornamentation

Torque Specifications

Rear Quarter Panel Moulding

Removal

NOTE: Removal steps in this procedure may contain installation details.

1.

2. NOTE: Discard the retaining clips.

• Make sure that the centre part of the clip is fully removed from the outer part of the clip. It is not possible to prevent the centre part of the clip falling into the body of the vehicle.

3. CAUTION: Take extra care not to damage the component.

4. NOTE: Discard the sealing plug.

Installation

1. To install, reverse the removal procedure.

Rear Spoiler

Removal

All vehicles

1. NOTE: The procedure must be carried out on both sides.

Refer to: A-Pillar Trim Panel (501-05 Interior Trim and Ornamentation, Removal and Installation).

3-door

NOTE: The procedure must be carried out on both sides.

2. Refer to: B-Pillar Upper Trim Panel - 3-Door (501-05 Interior Trim and Ornamentation, Removal and Installation).

5-door

3. NOTE: The procedure must be carried out on both sides.

Refer to: B-Pillar Upper Trim Panel - 5-Door (501-05 Interior Trim and Ornamentation, Removal and Installation).

All vehicles

4. NOTE: The procedure must be carried out on both sides.

Refer to: C-Pillar Upper Trim Panel (501-05 Interior Trim and Ornamentation, Removal and Installation).

5. NOTE: The procedure must be carried out on both sides.

Refer to: D-Pillar Trim Panel (501-05 Interior Trim and Ornamentation, Removal and Installation).

6. Refer to: Overhead Console (501-12 Instrument Panel and Console, Removal and Installation).

7. NOTE: The step must be carried out on both sides.

8. NOTE: The step must be carried out on both sides.

9. NOTE: The step must be carried out on both sides.

10. NOTE: The step must be carried out on both sides.

11.

12.

13. NOTE: The procedure must be carried out on both sides.

14. NOTE: The step must be carried out on both sides.

15. NOTE: The step must be carried out on both sides.

16.

17. NOTE: This step requires the aid of another technician.

Lower the headliner for access.

18.

19. NOTE: The step must be carried out on both sides.

Torque: 10 Nm

20. CAUTION: Take extra care not to damage the 20. wiring harnesses.

Installation

1. NOTE: Do not tighten the rear spoiler retaining nuts at this stage.

To install, reverse the removal procedure.

2. NOTE: Make sure that the gap is even between the rear spoiler and the rear quarter panel moulding and the rear spoiler is flush with the roof panel (use a suitable plastic straight edge).

3. NOTES:

Rear spoiler shown removed for clarity.

Loosen the rear spoiler retaining nuts.

4. NOTE: Rear spoiler shown removed for clarity.

Adjust the rear spoiler by rotating the adjustment studs clockwise and counter clockwise as necessary.

5. NOTE: Rear spoiler shown removed for clarity.

Torque: 7 Nm

6. NOTE: Make sure that the gap is even between the rear spoiler and the rear quarter panel moulding and the rear spoiler is flush with the roof panel (use a suitable plastic straight edge).

If the rear spoiler is not correctly adjusted, follow Steps 3 to 6 of the installation procedure until correct alignment is achieved.

Hood Badge

Removal

1. CAUTION: Remove any excessive adhesive from the hood.

Using a suitable tool or plastic spatula, remove the hood badge(s).

Installation

1. Clean the area prior to installation of the hood badge.

2. CAUTION: Using the centre of the grill as a starting point, install the hood badge to the dimensions shown.

• A - 25 mm / 0.9 inch
• B - 40 mm / 1.6 inch
• C - 50 mm / 1.9 inch

READ NEXT: