Range Rover Evoque: Bumpers
Front Bumper Cover
Removal
NOTE: Removal steps in this procedure may contain installation details.
1.
2.
3. WARNING: Make sure to support the vehicle with axle stands. Raise and support the vehicle.
4. NOTE: The step must be carried out on both sides. Refer to: Fender Splash Shield (501-02 Front End Body Panels, Removal and Installation).
5.
6.
7.
8. Torque: 4.5 Nm
9. NOTES:
The step must be carried out on both sides.
Do not disassemble further if the component is removed for access only.
Torque: 2 Nm
10.
11.
12.
13.
14.
15.
16.
17.
18. NOTE: The step must be carried out on both sides.
19.
Installation
1. To install, reverse the removal procedure.
Front Bumper
Removal
NOTE: Removal steps in this procedure may contain installation details.
1. WARNING: Make sure to support the vehicle with axle stands. Raise and support the vehicle.
2. Refer to: Front Bumper Cover (501-19 Bumpers, Removal and Installation).
3. NOTE: The step must be carried out on both sides.
Torque: 4.5 Nm
4. NOTE: The step must be carried out on both sides. Torque: 4.5 Nm
5. Torque: 4.5 Nm
6. Torque: 4.5 Nm
7. Torque: 48 Nm
Installation
1. To install, reverse the removal procedure.
Rear Bumper Cover
Removal
NOTE: Removal steps in this procedure may contain installation details.
1. NOTE: The procedure must be carried out on both sides. Refer to: Rear Lamp Assembly (417-01 Exterior Lighting, Removal and Installation).
2.
3. WARNING: Make sure to support the vehicle with axle stands. Raise and support the vehicle.
4. Remove the rear wheels and tyres.
Refer to: Wheel and Tire (204-04 Wheels and Tires, Removal and Installation).
5. CAUTION: Take extra care not to damage the component.
NOTE: The step must be carried out on both sides.
6.
7.
8. Torque: 4.5 Nm
9.
10. CAUTION: Take extra care not to damage the edges of the component.
11. NOTE: Do not disassemble further if the component is removed for access only. Torque: 4.5 Nm
12. NOTE: The procedure must be carried out on both sides. Torque: 4.5 Nm
13.
14.
15.
Installation
1. To install, reverse the removal procedure.
Rear Bumper
Removal
NOTE: Removal steps in this procedure may contain installation details.
1. WARNING: Make sure to support the vehicle with axle stands. Raise and support the vehicle.
2. Refer to: Rear Bumper Cover (501-19 Bumpers, Removal and Installation).
3. Torque: 30 Nm
Installation
1. To install, reverse the removal procedure.
Bumpers
Torque Specifications
READ NEXT:
Safety Belt System
Safety Belt System
Diagnosis and Testing
Principle of Operation
For a detailed description of the seatbelt system and operation, refer to the
relevant description and operation section of
the worksho
Air Bag Supplemental Restraint System
(SRS)
Component Location
COMPONENT LOCATION SHEET 1 OF 2
Battery
ECM (engine control module)
CJB (central junction box)
Passenger air bag
Overhead console
RCM (restraints control module)
Driver air
SEE MORE:
Diesel engined vehicles
Do not use RME (bio-diesel)
except in
the case of those proprietary diesel
fuels which contain a mix of up to 7%.
Land Rover vehicles can accept no
responsibility for damage caused by
using RME in concentrations greater
than 7%.
Use only high quality diesel fuel according to
EN590 or equi
Operating the tailgate
Ensure there is minimum space
of 1.0M
(39 in) above the rear of vehicle before
operating the tailgate. Insufficient space
may result in damage to the vehicle.
Do not operate the tailgate
if a cycle
rack is fitted to the tailgate. Remove any
cycles and/or racks before operating
the tailg
